v1.02 build 838 - May 2022 ------------------------------------- New Feature: LabSat will emit a ‘Beep’ as a notification of a buffer over or underflow event during record or replay. Time into the record/replay that the buffer event occurred will be stated in the corresponding .ini file under the ‘Buffer’ heading. New Feature: Network security can be enabled within the Labsat ‘LAN’ menu – this will password protect access to the internal SSD via ethernet. New Feature: Copying files from USB or SD card media to internal SSD now supported. New Feature: MAC address now displayed within the LabSat ‘About’ menu and on the ‘System Settings’ page of the webserver. Optimization: added support for Wi-Fi dongles using the MediaTek MT7601 chipset. Optimization: Adjustment to automatic gain control to optimise quality of recorded signals. Bug Fix: Telnet command including a play ‘from’ time now overrides the time set in the ‘Play Options’ menu. Bug fix: LabSat is no longer unable to record a new file if a .ini file from a previous recording is present on the SSD without a matching .LS3W file.
Known issue: If the RF channel frequency has been configured via the web interface, then accessing the constellation menu will require the settings to be changed before the user can exit the menu. Therefore, if checking the constellation settings from the front panel, use the ‘Status’ menu option rather than the constellation menu, to avoid having to change settings. Alternatively, to exit the constellations' menu without changing/updating the settings, open the web server and select ‘Exit front panel menus’.
v1.01 build 688 - May 2021 ------------------------------------- Improvements the the RF channel synchronisation.
v1.01 build 675 - August 2020 ----------------------------- Added support for M9 receiver. Implements 15-second boot delay to improve large capacity SSD handling. GNSS engine variant added to the 'About' menu. Bug Fix: File time stamp is now correct when changing between manual and GPS UTC. Bug Fix: Play 'For' telnet command response corrected. Bug Fix: Webserver 'Mute' tick boxes now stay ticked if not disabled before the replay ends. Bug Fix: Webserver freuency chart can now be saved as a PNG image.
v1.00 build 668 - August 2019 ----------------------------- New Feature: Support added for SamSung EVO 860 4TB SSD. New Feature: Support added for SamSung 7.68TB PM883 SSD. New Feature: Support added for Synology NAS connectivity. Web server interface updated. New Feature: SSD formatting updated to include GPT table. Bug Fix: Power button no longer bounces during power down.
v1.00 build 461 - August 2018 ----------------------------- Bug Fix: Telnet - Conf:? now updated correctly. Necessary changes made to support new Picozed hardware. Web Server interface version updated.
v1.00 build 414 - May 2018 --------------------------
New Feature: RS232 Log File mode. New Feature: External Synchronisation (record/replay start sync). New Feature: Export current configuration. New Feature: Wifi Dongle. New Feature: Replay Only Support. New Feature: Formatting SSD from other settings to EXT4 supported. Bug Fix: Telnet - Media:List now returns the correct file name and length. Other minor bug fixes and further improvements also made.
v1.00 build 260 - June 2017 --------------------------- New Feature: Web Server interface, Telnet Remote control and Arbitrated CAN filter files.
v1.00 build 237 - April 2017 ---------------------------- New Feature: recording/replaying external data (CAN,RS232,Digital). NOTE: Telnet and External Sync features are not supported in this release. Support for these features will be implemented with the next firmware release.
v1.09 b1099 - December 2018 Changes for production process.
v1.08 b1083 - May 2017 Further improvements made to USB media combating the 'file system error'. Improvements for CAN arbitration timing.
v1.08 b1072 - January 2017 New firmware version to support the new UBLOX receivers being used within LabSat 3.
v1.06 b1036 - June 2015 Stability improvements for USB Media. Improvements to the file system when creating large scenarios.
v1.05 b1033 - January 2015 New CAN Arbitration functionality implemented - allowing the user to capture CAN in a time-stamped text file. Added support for defining replay and record times from the LabSat 3 front panel.
v1.04 b956 - May 2014 Enables the user to use remote access/control over Ethernet.
NOTE: Only LabSat 3 customers with unit serial numbers 033353 or above can use this upgrade to enable remote control. LabSat 3 customers with unit serial numbers lower than 033353 (purchased before the end of March 2014) will need to send the unit in (RL UK or USA office) for an upgrade.
v1.03 b852 - April 2014 Improves the CAN capture and replay functionality.
v1.02 b844 - February 2014 Supports USB functionality - Host USB Storage device connectivity & standard USB outputs NMEA from internal LabSat 3 receiver. upgrade for SD card support to include 32GB, 64GB & 128GB cards. Note approved SD cards only - see LabSat 3 manual.
v1.01 b838 - February 2014 Supports the new bootloader further optimising the internal battery performance.
v1.01 b831 - November 2013 Fixes signal drop out - drop outs no longer present in replay when 'OK' was pressed during recording. Adds 'Loop' function to play menu - continuous replay of selected scenario. Auto-off disabled when connected to external power.
v1.00 b821 - November 2013 Initial release version.
Feature: NAVIC (formerly known as IRNSS) L5 signal has been added to SatGen.
Feature: The carrier-to-noise-density ratio C/N0 is no longer displayed as an absolute value, but it is now expressed as attenuation from the pure signal level. C/N0 can now be reduced by up to 15 dB-Hz in 1 dB-Hz steps. If attenuation is not zero, the same amount of noise is added to all simulated signals.
Feature: The anti-spoofing flag transmitted in the GPS L1C/A navigation message is now automatically set depending on the selected signals:
When L1C/A is simulated, but neither L1P nor L2P: The anti-spoofing flag is ON. This tells the receiver that the encrypted Y-Code is transmitted instead of the public P-Code on L1 and L2. SatGen can't simulate the Y-Code, but we set the anti-spoofing flag to ON, because some receivers refuse to work if that flag is OFF.
When L1C/A is simulated together with any of L1P and L2P signals: The anti-spoofing flag is OFF. This tells the receiver that the public P-Code is transmitted on L1 and L2.: HASP drivers version 8.13.
Optimization: The algorithm responsible for choosing which satellites to simulate in real time mode (when the number of satellites is restricted) has been changed. It now offers better satellite geometry.
Optimization: RealTime window is now slightly wider to show more satellites by default (it can always be resized if necessary).
Optimization: Ionospheric delay algorithm improved for situations when the receiver flies through the ionosphere.
Optimization: Simulation performance improved by 5-10% (depending on the selected signals).
Optimization: Improved reliability of Real Time simulations– unless a serious problem occurs, individual buffer underruns should not affect the continuity of the signal.
Bugfix: U-centre KML format from LabSat 3 HDD now supported.
Bugfix: The simulation without a dongle was interrupted too late, not exactly after 120s.
Support for latest version of CAN Output Plugin and Turntable
2.7.1 - July 2014
Minor bug fixes to the video sync functionality. Support added for LabSat 3 converted file formats.
2.6.14 - January 2013
Addition of Beidou/Compass channel support for Labsat2 (fw2.0 or greater). Minor bug fixes.
22.214.171.124 - July 2012
Bug fix for scenario converter software. Support for new LabSat USB boards.
2.5.6 - May 2012
Addition of Video sync. Addition of NMEA Serial proxy. Turn table support - #2236: Software crashes when loading truncated file - #2423: Default save location crash More stability enhancements.
2.3.5 - May 2011
Bug fixes - #1799: Manually entered file name without extension crashed software - #1800: Manually entered file name in protected location showed no error - #1807: Scenario converter was looking for a lower case extension - #1808: ScenarioFactory expected lower case extension - #1812: Possible IndexOutOfBounds in NmeaParser More stability enhancements.
2.2.1 - March 2011
LabSat 1 Compatibility. Bug fixes - #1714: Record after a replay passes no RF to internal GPS monitor
2.1 - February 2011
- Full multi-bit support, with the ability to record a single channel in 1 bit or 2 bit mode, or both channels in 1 bit. It will also allow you to replay 2 bit scenarios as 1 bit, whilst displaying the current mode with other critical information. - Independent channel attenuation - Channel mute: you can now simulate temporary drop outs or replay only one channel from a 2 channel recording by muting the other - Disable synthesizers at end of replay: this prevents residual RF transmission at the end of a scenario causing noise on the receiver - Add a description to a scenario when recording - Display scenario information in a pop-up window, together with details of the LabSat used to record the scenario, the description, and options used - Automatic start and replay: passing a scenario name as a command line argument will now cause the software to start up and commence replay immediately. A-r switch enables repeat. - Firmware version reporting - the about screen now shows hardware, firmware and FPGA version information - API - the library assembly is now documented and COM registered to allow interaction from numerous other programming environments. Samples provided in C#, Windows Powershell (scripting), C++, MatLab - Supports temporary upgrades to Record + Replay functionality from Replay only or Record only. This means we can now offer a week's upgrade at a low cost by sending you an upgrade file, for you to evaluate the full LabSat record and replay functionality. Contact your dealer for more information!
2.0 - January 2011
First release of 2.0 software supporting LabSat 2. - Buffer level display in real-time and 10 minute history - GPS monitor with real-time display and 10 minute speed history
2.5.0 - October 2017 Bug fix: conversion of very specific multi-file LS3 scenarios finishing prematurely half way through. Bug fix:"All files *.*" input file filter has now been removed, because it allowed the users to load non-LabSat files.
2.4.5 - June 2017 Added support for conversion to LabSat 3 Wideband file format.
2.4.1 - February 2015 Feature: Message "LabSat 3 Triple Constellation files are not supported" is displayed when the user tries to open a triple constellation file. Feature: Added "All LabSat files" and "All files" filters to the OpenFileDialog.
2.3.3 - February 2015 Added support for leap second scenarios.