LabSat 3 Wideband Recording Setup
Centre frequency
Band 1:
MHz
1575Mhz-1575Mhz
Band 2:
MHz
1575Mhz-1575Mhz
Band 3:
MHz
1575Mhz-1575Mhz
 
Saved record profiles:
 
Read current profile
 

Profile name:
 

Save and Apply
 
Save only
 

Delete selected profile
 
LabSat 3 Wideband File Management
Current directory:  
SubDirectories
DirectoryRenameDelete
No subdirectories found
Create directory
 
Recordings:
FilenameLengthBandwidthQuantisationBand 1Band 2Band 3PlayRenameDeleteDownload
No recordings found
Current recording settings:
Record 1 band centred at 1MHz with a bandwidth of 1MHz and using 1MHz quantization.
Digital IO something or other
Recordings will require   MBytes/minute (   GBytes/hour). Currently there is sufficient free space to record for 1 nanosecond.
LabSat 3 Wideband GNSS Monitor
 
 
Current position
Time :------
Latitude :------
Longitude :------
Height above elipsoid :------
Horizontal velocity :------
Heading :------
Signal level controls:
Lock signal level controls together
Band 1 ---- MHz :
dB Mute
Band 2 ---- MHz :
dB Mute
Band 3 ---- MHz :
dB Mute
Note: Monitor only tracks L1 band signals and is for indication only. When recording all signals present on the input port will be shown regardless of recording frequency configuration. When replaying monitor will report no signals if the L1 band was not recorded even if other GNSS signals are present.
LabSat 3 Wideband System Setup
Network options:
Enable DHCP
IP address
Subnet mask
Default gateway
Refresh


Clock options:
Clock source: TCXO OCXO External 10.0 MHz clock input
Enable 10.0 MHz clock output

Apply changes
 
LabSat 3 Wideband Digital IO Setup
Sample rate:
Time accuracy:   (  )
Max baud rate:  
Digitized channel select
ChannelSignal sourceRecord inputReplay output
Channel 1  
Channel 2  
Channel 3  
Channel 4  
Ground connections are available on pins 4, 5, 7, 9, 19, 20, 21, 33 and 34.
CAN record options:
Record arbitrated CAN to text log file
Silent record (No Ack from LabSat)
Arbitrated CAN 1 baud rate:
Arbitrated CAN 2 baud rate:
Apply changes
 
CAN replay options:
Use log file for CAN replay if available
LabSat logoLabSat 3 Wideband

Small, battery powered, multi-constellation and multi-frequency Global Navigation Satellite Simulator. LabSat 3 WIDEBAND captures and replays more GNSS signals at much higher resolution than before.

With three channels, a bandwidth of up to 56MHz and 6 bit sampling, LabSat 3 WIDEBAND can handle almost any combination of constellation and signal that exists today, with plenty of spare capacity for future planned signals.

LabSat 3 WIDEBAND can record and replay the following signals:

  • GPS: L1 / L2 / L5
  • GLONASS: L1 / L2 / L3
  • BeiDou: B1 / B2 / B3
  • QZSS: L1 / L2 / L5
  • Galileo: E1 / E1a / E5a / E5b / E6
  • SBAS: WAAS, EGNOS, GAGAN, MSAS, SDCM
  • IRNSS
Unit type: LabSat3
Unit serial number: 00000
Unit firmware version: 00000
Unit hardware revision: 00000
Internal drive type: SSD
Internal drive capacity: 1000 GBytes
Internal drive free space: 100 GBytes
 
 
Racelogic support
 
+
Frequency Setup
Select signal display
GPS

Galileo

GLONASS

BeiDou

Other

Show individual signals
Bandwidth
Number of channels
1 Band 2 Bands 3 Bands
Signal quantization
Current quantization:
Maximum in this mode:  
Digital IO
Resolution:   (  )
Max baud rate:  
 
 
Record and replay
System status:
Currently playing:  
Time:   out of  
Stop replay
 
Currently recording:  
Time:  
Stop recording
Currently idle.
Replay options:
Loop replay
Start replay at:
Replay for:
 
Record options:
Record for:
File name:
Start recording
 
GNSS monitor
Constellation
GPS
GLONASS
Galileo

GPS
BeiDou
Galileo

GLONASS
BeiDou

 
Digital IO setup
IO options
 
System setup
Setup options
 
About LabSat 3 Wideband
About options
<<
Click here to save chart as png image
Connected to LabSat 3 Wideband SN: 00000
Demo mode - Some features are unavailable
Current status: idle
CAN1: Idle CAN2: Idle
 
X
text
text
< Previous
Next >