SatGen GNSS Signal Simulation

Posted in Other

Novatel SatGen screenshotSatGen Signal Simulation Software can be used with LabSat Wideband to simulate all major constellations and signals.

If you need to record, replay or simulate multi-frequency, multi-constellation signals, then we have an easy to use, and cost-effective solution.

SatGen software allows you to create a GNSS RF I&Q or IF data file based on a user-generated trajectory file that can be replayed on a LabSat GNSS Simulator. This allows you to simulate almost any kind of test, at a set time and date, anywhere in the world.

For example, say you are based in Europe, but your GPS devices will be deployed throughout the world. With SatGen you can create a test scenario for virtually any location, including hostile areas for which live-sky field testing might be impossible.

This allows you to verify that your GPS equipment performs as required, in a variety of locations that may be geographically remote from your facility.

LabSat Wideband conncted to GNSS engineSatGen complements the LabSat range of GNSS simulators, and is available in single, dual, triple and multi-frequency/multi-constellation versions.

Of course, LabSat can record and replay live data, but creating an artificial scenario allows you to precisely control the data content, create a ‘gold standard’ file for carrying out true comparisons between receivers.

From your bench you can try different acceleration levels, crossing different time zones, the equator,leap second, roll-over and many hard to replicate tests.

The latest version of SatGen can be used to create a single scenario containing all the upper and lower L Band signals for GPS, Galileo, GLONASS, and BeiDou, and will take advantage of the LabSat 3 Wideband’s ability to read RF data at up to 95 MB/s.

GPS L1L2CL5 Glonass L1L2  BeiDou B1B2   Galileo E1E5E6

What constellations & signals can I create?

  • Single Constellation - Create single constellation scenario files for GPS L1/ Galileo E1, GLONASS L1 or BeiDou B1
  • Dual Constellation - Create dual or single constellation scenario files for GPS L1/ Galileo E1, GLONASS L1 or BeiDou B1
  • Triple Constellation - Create triple, dual or single constellation scenario files for GPS L1/ Galileo E1, GLONASS L1 or BeiDou B1
  • Wideband - Create LabSat 3 Wideband scenario files for:
    GPS L1C/A, L1P, L1M, L2C, L2P, L2M, L5 ( L1M, L2M noise created only)
    Galileo E1, E5A, E5B, E6 (coming soon)
    GLONASS L1OF, L2OF
    BeiDou: B1I, B1-2I, B2I (BeiDou B1 special almanac including BeiDou future satellites)
  • Real-Time – Create real-time GPS/ Galileo E1, GLONNASS, BeiDou L1 signals with the additional LabSat RT dual constellation system

How does SatGen work?

SatGen can be used to create a scenario which replicates very high dynamic conditions, allowing engineers to test their systems work in all environments. You could simulate an aircraft taking off and going into a vertical climb up to 30,000 feet, and then performing a high g-turn at this altitude, all without leaving your bench!

Creating your own scenarios couldn't be easier. If you have an NMEA file which contains GGA data, then you can import this directly into the software or alternatively, you can start from scratch by creating a route in Google Earth, or build a profile using simple user commands.

Developed with the user in mind, this software allows you to create a static scenario, where a position can be manually inserted or easily determined using the integrated Google Maps screen. You can also draw a route by simply clicking-on a series of locations on the map.

SatGen-GPS-Simulation-Software

SatGen includes a range of predefined command buttons and scenario examples (including figure-of-eight, circle around a point and aircraft take-off). These pre-set scenarios allow you to test a device by making a few simple clicks.

To find out more about how SatGen can be used to simulate GNSS scenarios, contact .


Is SatGen right for you? Why not try it out?

To enable you to experience the full power of the SatGen Simulation Software, we provide a demonstration version which will allow you to try all new features.

Fill out my online form.
 

It's a full copy of the SatGen software but is restricted to create GPS-only scenarios (no other constellations) for only 120 seconds.

This will allow you to trial the use of SatGen in your own test facility or laboratory.

Please note that the SatGen v3 Simulation Software requires a 64 bit windows operation system and will not install on a 32 bit system.

To receive a free copy of this demo version, please complete the form on the left.

For more information on SatGen or a quote, please contact your local LabSat distributor or RACELOGIC directly.

contact us

SatGen GNSS Signal Simulation Software

Posted in Other

Novatel SatGen screenshotSatGen Signal Simulation Software can be used with LabSat Wideband to simulate all major constellations and signals.

If you need to record, replay or simulate multi-frequency, multi-constellation signals, then we have an easy to use, and cost-effective solution.

SatGen software allows you to create a GNSS RF I&Q or IF data file based on a user-generated trajectory file that can be replayed on a LabSat GNSS Simulator. This allows you to simulate almost any kind of test, at a set time and date, anywhere in the world.

For example, say you are based in Europe, but your GPS devices will be deployed throughout the world. With SatGen you can create a test scenario for virtually any location, including hostile areas for which live-sky field testing might be impossible.

This allows you to verify that your GPS equipment performs as required, in a variety of locations that may be geographically remote from your facility.

LabSat Wideband conncted to GNSS engineSatGen complements the LabSat range of GNSS simulators, and is available in single, dual, triple and multi-frequency/multi-constellation versions.

Of course, LabSat can record and replay live data, but creating an artificial scenario allows you to precisely control the data content, create a ‘gold standard’ file for carrying out true comparisons between receivers.

From your bench you can try different acceleration levels, crossing different time zones, the equator,leap second, roll-over and many hard to replicate tests.

The latest version of SatGen can be used to create a single scenario containing all the upper and lower L Band signals for GPS, Galileo, GLONASS, and BeiDou, and will take advantage of the LabSat 3 Wideband’s ability to read RF data at up to 95 MB/s.

GPS L1L2CL5 Glonass L1L2  BeiDou B1B2   Galileo E1E5E6

What constellations & signals can I create?

  • Single Constellation - Create single constellation scenario files for GPS L1/ Galileo E1, GLONASS L1 or BeiDou B1
  • Dual Constellation - Create dual or single constellation scenario files for GPS L1/ Galileo E1, GLONASS L1 or BeiDou B1
  • Triple Constellation - Create triple, dual or single constellation scenario files for GPS L1/ Galileo E1, GLONASS L1 or BeiDou B1
  • Wideband - Create LabSat 3 Wideband scenario files for:
    GPS L1C/A, L1P, L1M, L2C, L2P, L2M, L5 ( L1M, L2M noise created only)
    Galileo E1, E5A, E5B, E6 (coming soon)
    GLONASS L1OF, L2OF
    BeiDou: B1I, B1-2I, B2I (BeiDou B1 special almanac including BeiDou future satellites)
  • Real-Time – Create real-time GPS/ Galileo E1, GLONNASS, BeiDou L1 signals with the additional LabSat RT dual constellation system

How does SatGen work?

SatGen can be used to create a scenario which replicates very high dynamic conditions, allowing engineers to test their systems work in all environments. You could simulate an aircraft taking off and going into a vertical climb up to 30,000 feet, and then performing a high g-turn at this altitude, all without leaving your bench!

Creating your own scenarios couldn't be easier. If you have an NMEA file which contains GGA data, then you can import this directly into the software or alternatively, you can start from scratch by creating a route in Google Earth, or build a profile using simple user commands.

Developed with the user in mind, this software allows you to create a static scenario, where a position can be manually inserted or easily determined using the integrated Google Maps screen. You can also draw a route by simply clicking-on a series of locations on the map.

SatGen-GPS-Simulation-Software

SatGen includes a range of predefined command buttons and scenario examples (including figure-of-eight, circle around a point and aircraft take-off). These pre-set scenarios allow you to test a device by making a few simple clicks.

To find out more about how SatGen can be used to simulate GNSS scenarios, contact .


Is SatGen right for you? Why not try it out?

To enable you to experience the full power of the SatGen Simulation Software, we provide a demonstration version which will allow you to try all new features.

Fill out my online form.
 

It's a full copy of the SatGen software but is restricted to create GPS-only scenarios (no other constellations) for only 120 seconds.

This will allow you to trial the use of SatGen in your own test facility or laboratory.

Please note that the SatGen v3 Simulation Software requires a 64 bit windows operation system and will not install on a 32 bit system.

To receive a free copy of this demo version, please complete the form on the left.

For more information on SatGen or a quote, please contact your local LabSat distributor or RACELOGIC directly.

contact us

GNSS 频率指南 - LabSat 3 Wideband

Posted in Other

这款有用的应用程序可用于选择和查询 GNSS 频率和信号位置。GNSS 频率指南位于 LabSat 3 Wideband 内部网络界面上,可让您通过电脑设置和管理 GNSS 测试程序。您可在此查看网络界面演示。

如何使用 GNSS 频率指南

移动上图中的彩色带宽方块以更改中心频率(按下鼠标左键并左右拖动)。选择您的带宽要求,选择您需要的频率,查看可用的量化等级。

 
选择信号显示
 
 
 
GPS
   
     Gallileo
   
     GLONASS
   
     北斗
   
     其他
   
显示单个信号

选择带宽
10 MHz    30 MHz    56 MHz   

选择信号频带
1 频带    2 频带    3 频带

信号量化
Current quantization:
&nbsp

中心频率
移动上方图表中的彩色带宽方框可更改中心频率(按住鼠标左键向左或向右拖动)
频带 1: 1575Mhz-1575Mhz
1575Mhz
频带 2: 1575Mhz-1575Mhz
1575Mhz
频带 3: 1575Mhz-1575Mhz
1575Mhz

示例:

  • 1) 选择信号显示:包括“显示单个信号”在内的所有信号。
  • 2) 选择“56MHz”带宽。
  • 3) 选择一个信号频带“1 频带”。
  • 4) 注意量化为 3 位。
  • 5) 移动红色方框以选择中心频率。
  • 6) 选择不同的带宽/通道来了解全部能力。

 

带宽设置

LabSat 3 Wideband 有三种带宽设置。56MHz、30MHz 和 10MHz。

GNSS 信号的带宽各不相同,例如 GPS L1 C/A 编码信号的带宽为 24MHz。但由于信号设计的原因,9.66MHz 的带宽将能捕获足够的数据让所测试的接收器进行信号采集、追踪和导航,就如同使用 LabSat 3 单星座、双星座和三星座装置。

诸如 Galileo E1 PRS 信号等具有不同信号设计的其它信号,拥有 46MHz 的带宽,以及涵盖整个带宽的信号设计。

许多其它信号拥有与 GPS L1/L2 P 编码和 M 编码类似的要求。LabSat 3 Wideband 专门设计用于捕获所有这些信号。

频率设置:

LabSat 3 Wideband 专门设计用于捕获和回放高位 L 波段 (1559 - 1610Mhz)和低位 L 波段 (1164 - 1300MHz) 的 GNSS 信号。

量化设置

LabSat 3 Wideband 可在以下量化等级录制和回放 GNSS 信号:

  • 3 位(3 位 I + 3 位 Q)
  • 2 位(2 位 I + 2 位 Q)
  • 1 位(1 位 I + 1 位 Q)

SatGen Signal Simulation Software

Posted in Other

Novatel SatGen screenshotSatGen Signal Simulation Software can be used with LabSat Wideband to simulate all major constellations and signals.

If you need to record, replay or simulate multi-frequency, multi-constellation signals, then we have an easy to use, and cost-effective solution.

SatGen software allows you to create a GNSS RF I&Q or IF data file based on a user-generated trajectory file that can be replayed on a LabSat GNSS Simulator. This allows you to simulate almost any kind of test, at a set time and date, anywhere in the world.

For example, say you are based in Europe, but your GPS devices will be deployed throughout the world. With SatGen you can create a test scenario for virtually any location, including hostile areas for which live-sky field testing might be impossible.

This allows you to verify that your GPS equipment performs as required, in a variety of locations that may be geographically remote from your facility.

LabSat Wideband conncted to GNSS engineSatGen complements the LabSat range of GNSS simulators, and is available in single, dual, triple and multi-frequency/multi-constellation versions.

Of course, LabSat can record and replay live data, but creating an artificial scenario allows you to precisely control the data content, create a ‘gold standard’ file for carrying out true comparisons between receivers.

From your bench you can try different acceleration levels, crossing different time zones, the equator,leap second, roll-over and many hard to replicate tests.

The latest version of SatGen can be used to create a single scenario containing all the upper and lower L Band signals for GPS, Galileo, GLONASS, and BeiDou, and will take advantage of the LabSat 3 Wideband’s ability to read RF data at up to 95 MB/s.

GPS L1L2CL5 Glonass L1L2  BeiDou B1B2   Galileo E1E5E6

What constellations & signals can I create?

  • Single Constellation - Create single constellation scenario files for GPS L1/ Galileo E1, GLONASS L1 or BeiDou B1
  • Dual Constellation - Create dual or single constellation scenario files for GPS L1/ Galileo E1, GLONASS L1 or BeiDou B1
  • Triple Constellation - Create triple, dual or single constellation scenario files for GPS L1/ Galileo E1, GLONASS L1 or BeiDou B1
  • Wideband - Create LabSat 3 Wideband scenario files for:
    GPS L1C/A, L1P, L1M, L2C, L2P, L2M, L5 ( L1M, L2M noise created only)
    Galileo E1, E5A, E5B, E6 (coming soon)
    GLONASS L1OF, L2OF
    BeiDou: B1I, B1-2I, B2I (BeiDou B1 special almanac including BeiDou future satellites)
  • Real-Time – Create real-time GPS/ Galileo E1, GLONNASS, BeiDou L1 signals with the additional LabSat RT dual constellation system

How does SatGen work?

SatGen can be used to create a scenario which replicates very high dynamic conditions, allowing engineers to test their systems work in all environments. You could simulate an aircraft taking off and going into a vertical climb up to 30,000 feet, and then performing a high g-turn at this altitude, all without leaving your bench!

Creating your own scenarios couldn't be easier. If you have an NMEA file which contains GGA data, then you can import this directly into the software or alternatively, you can start from scratch by creating a route in Google Earth, or build a profile using simple user commands.

Developed with the user in mind, this software allows you to create a static scenario, where a position can be manually inserted or easily determined using the integrated Google Maps screen. You can also draw a route by simply clicking-on a series of locations on the map.

SatGen-GPS-Simulation-Software

SatGen includes a range of predefined command buttons and scenario examples (including figure-of-eight, circle around a point and aircraft take-off). These pre-set scenarios allow you to test a device by making a few simple clicks.

To find out more about how SatGen can be used to simulate GNSS scenarios, contact .


Is SatGen right for you? Why not try it out?

To enable you to experience the full power of the SatGen Simulation Software, we provide a demonstration version which will allow you to try all new features.

Fill out my online form.
 

It's a full copy of the SatGen software but is restricted to create GPS-only scenarios (no other constellations) for only 120 seconds.

This will allow you to trial the use of SatGen in your own test facility or laboratory.

Please note that the SatGen v3 Simulation Software requires a 64 bit windows operation system and will not install on a 32 bit system.

To receive a free copy of this demo version, please complete the form on the left.

For more information on SatGen or a quote, please contact your local LabSat distributor or RACELOGIC directly.

contact us